How To: Remove a Shark Bite Fitting Without a Special Tool - Adjustable Wrench Trick
Here's a fast easy way to remove and disconnect your Shark Bite quick connect fitting, without a special tool to do it. We'll show you a awesome little trick using an adjustable wrench. This will work an all different size Shark Bite fittings.
How To: Build and install a cheap dumbwaiter in your home
Home improvement expert Danny Lipford shows how to build and install a cheap dumbwaiter in your home in this video tutorial.
How To: Adjust the Alignment of Cabinet Doors
Poor alignment of cabinet doors will cause a kitchen to look run-down and may be embarrassing to the homeowner. Luckily, with a single screw driver and a little ambition, the door alignment can look brand new.
How To: Cut Perspex or acrylic sheet with a circular or jigsaw
Wondering how to cut Perspex (or acrylic glass) easily? When cutting Perspex at home, you're more or less limited to using circular saws and jigsaws. For cutting straight lines, the circular law works best; for curvy lines, you'll want to use your jigsaw. For more information, including step-by-step instructions on cutting your own acrylic sheet, watch this DIY home tutorial.
How To: Completely remove an interior door in your home
Have a new door that needs installed? Well, first thing you're going to have to do is remove the old one! Check out this home improvement video tutorial on how to completely remove an interior door in your home.
How to Build a Shed, Part 13: Installing a 3-Tab Asphalt Shingle Roof
Henry shows you how to install a 3 tab asphalt shingle roof in this video. This video covers everything from the type of roofing felt to use, making the starter strips, layout with chalk lines right through to making and installing the ridge caps.
How To: Remove a threaded stud from a threaded hole
Ultimate Handyman demonstrates how to remove a threaded stud from a threaded hole. You will often find threaded studs when you are doing car repair. First, remove the nut from the stud. Then, spray it with lubricant. Next, screw the nut back on the stud. Screw another nut on top of the first nut. Grip the bottom nut with a wrench while tightening the top nut. Grip the bottom nut and turn it in a counter clockwise direction. The stud should then pull out of the threaded hole. It may be difficu...
How To: Change Replace Freezer Light Bulb and Cover Kenmore Refrigerator
This video will show you how to remove the freezer light bulb cover in your Kenmore refrigerator. It's pretty easy to do, but not breaking the plastic light cover can be tricky.
How To: Install Laminate Flooring on Stairs
Installing Laminate Flooring on Stairs Laminate flooring can be installed on a flight of stairs, and this process can also be used when installing laminate on a floor and having to drop down a step to a sunken room.
How To: Do a 16 inch layout on stud wall
Bob Schmidt from Home Remodel Workshop demonstrates how to frame a wall 16 inches on center. His tutorial is especially helpful, so pay attention to his tips, tricks, and specific techniques.
How To: Fix and repair a dripping faucet
James from J&C Home Repair explains how to fix a bathroom faucet. He shows how to turn off the water supply to the faucets and tells you exactly what tools you will need. He demonstrates how to remove the faucet handle and the valve using common household tools, and recommends taking the parts to the hardware store to make sure you get the correct replacement parts. This video shows that repairing a faucet is a simple job that anyone can do. You don't need to call a plumber for this!
How To: Repair a dryer by replacing the support rollers
The drum support rollers are usually in the same spot on every dryer, no matter the brand. They will be below the drum. In order to remove the rollers, you need to open the dryer's cabinet and remove the drum. Perhaps you will notice that the left roller is more worn out than the right one. This is a common occurrence, but you need to replace both at the same time. Be sure to remove the nut before you remove the roller. Don't use more than one drop of oil on the hub as too much oil will aid t...
How To: Fill and repair holes in ceramic tile
Fixing holes in glazed ceramic tile can be very tricky. This is a solution that may not be perfect but it will provide a big improvement to your situation. You will need some polyester resin, which is often used to repair car bodies. Mix up some of the resin and apply it to the holes in the tile making sure that you overfill the holes. As it dries but while it is still rubbery take a razor blade and trim off the excess resin. Take some 600 grit sandpaper and sand the resin smooth. Wet the san...
How To: Repair holes in plasterboard walls
Plaster walls, although popular homebuilding materials, are notoriously easy to damage. Door handles, elbows and moving furniture are all great at putting holes in plasterboard walls, holes which, thankfully, only take an hour or so to patch up. Stumped as to how to do it? Watch this video tutorial to learn how to repair these holes on your wall.
How To: Construct Scaffolding
Tim Carter demonstrates why simple pipe scaffolding is an excellent tool to use for outdoor painting projects.
How to Build a Shed, Part 11: Installing Fascia Boards & Soffit Materials
The fascia boards and soffit material installation is very important. This is the finishing part of the shed. Henry shows you how to do this in great detail and get perfect results. In this video he shows you how to use his exclusive jig to make it easy to install long trim without any help!
How to Build a Shed, Part 9: Building & Installing Gable Ladders (Rakes)
Using ladders (Rakes) to build your gable overhangs on the shed is one of the fastest and easiest ways to do this. Henry shows you how to layout, build and install the ladders on our shed.
How To: Salvage a clogged caulk tube
How do you salvage a clogged caulk tube? In this Quick Tips with Chuck Miller video, you will see there is an ingenious and simple way to salvage a clogged caulk tube. Take a utility knife and simply make a slice on the side of the caulk tube nozzle. Probably the entire length of the nozzle is clogged and you may not be able to clear it with a wire or nail. After slicing it, take a sharp tool and remove the clogged material from the nozzle and clean it up. Then wrap the nozzle with electrical...
How To: Tighten radiator valves
In this video you will learn how to tighten radiator valves using a spanner and water pump pliers. If you find that your radiator valves are leaking, follow these simple steps to remedy the situation: If you take a look at your lock shield valve, you may see signs that it has been leaking. Grip the valve with a pair of water pump pliers. This will prevent you from breaking the copper pipe. Tighten in a clockwise direction. Feel with your fingers to make sure there are no more leaks.
How To: Caulk a sink using the dab method
This video demonstrates how to caulk a sink. For this project, you will need a tube of caulk, a towel, and an X-acto knife.
How To: Cut the perfect inside corner with a miter saw
This video, from Superior Building Supplies, demonstrates the proper technique for cutting the inside corners of crown molding. The presenter suggests downloading several diagrams from the Superior Building Supplies website. These diagrams show the correct position of the miter for several different cuts. When using a miter saw think of the fence as the ceiling and the table as the wall. Cuts for inside corners will always be made using 45 degree angles on your miter saw. Using these techniqu...
How To: Attach Timber to Concrete Using Concrete Anchors
How to install concrete anchors.How to attach timber / wood to concrete or any other SOLID masonry surface using masonry anchors / DynaBolts. DynaBolts (that's the name for this particular anchor in Australia. They are know by other names in other countries) are the ideal anchor for attaching almost anything to solid masonry such as concrete. This video will look at attaching timber to a concrete floor.
How To: Install a T-Mold Transition Between Laminate & Ceramic Tile
Installing a T Mold Transition Between Laminate and Ceramic Tile There are several different types of laminate transitions that you may need when installing laminate flooring. Each one is used specifically for where the laminate flooring ends, such as where the laminate stops at ceramic tile. Other transitions are used where the laminate ends at carpet, vinyl flooring, a threshold or a step down such as a sunken living room or stairs.
How To: Build a PVC greenhouse
In this tutorial, we learn how to build a PVC greenhouse. The dimensions of this will be 12' x 18'. First, you will use 1/2" PVC pipe that is 12' long that crosses in the middle to make a "t" shape. The frame can be made of treated 2'x 4's. Once you have the frame up, you can use thick plastic to securely cover the pipe and wood and clamp it into place. Once you have this done, you can place your tables inside of the greenhouse and start growing your plants! If you notice the plastic not hold...
How To: Cut Trafficmaster Allure flooring with your hands
One of the distinguishing aspects of Trafficmaster Allure vinyl flooring is that it requires very little effort to cut the pieces to whatever length you need. All you do is score a line across the piece, then fold it in half! It snaps cleanly into two new pieces. This quick video features a man remodeling his office cutting a piece himself in only 26 seconds, using only a ruler and a knife to score the wood before he folds it.
How To: Build a simple beam bridge
Stuck on one side of a river or ditch? If you are stranded with no other way to get to your destination you will need to build a bridge! Without many supplies, your best bet is a beam bridge which can be made with just a single piece of wood. This video will show you how to get from one place to another.
News: The World's Biggest Machine
Introducing the Bagger 288, built by Krupps in Germany. Weighing in at 45,000 tons, this bad boy is the biggest moving machine on the planet.
How To: Restore rusty ceiling grid systems
Update your nasty, ugly ceiling grid in your home or office. With this video tutorial, see how to restore rusty ceiling grid systems. Ceiling Armor Grid Cover will update rusty and discolored ceiling grid systems for a fraction of the cost of replacement. This unique cover snaps on to a standard grid system without any special preparation. This washable solid vinyl cover is suitable for standard ceiling grids in kitchens, restaurants, bakeries, pools, rest rooms and outdoor ceiling locations.
How To: Install a Split Jamb Door
Let Home Depot show you what it takes to install a split jamb door and the tools needed for this relatively easy job. Go step-by-step in this straightforward project, from centering and leveling the new door to placing shims and where to drive the nails. For more, or to get started on your own split jamb door installation project, watch the video on Dailymotion.
How To: Build a playground slide
In this video tutorial, you'll find instructions for building a standard joist design playground slide, supported by 3-by-4 posts and secured with galvanized fasteners. All fasteners exposed to the outdoors must be weather-resistant, galvanized, zinc-coated brass or stainless steel. Standard homeowner tools are all you'll need to complete your slide—a tape measure, post-hole digger, circular saw, sawhorses and a level. A good drill/driver is a great tool if using decking screws as fasteners. ...
How To: Install a window in a metal frame
A good way to install a window in a metal frame construction is to use some light gauge angle and screw it onto the sides of the window leaving a 10mm space for plaster. A flat head, self tapping screw is used to fix the window to the frame. Watch this video tutorial for a demonstration on how to install a window in a metal frame.
How To: Tie a string line
Are you trying to construct your dream house with your own two hands? Learn the tricks of the trade and watch this video tutorial on how to tie a string line.
How To: Use a spirit level when bricklaying
This video shows you how to use a spirit level when bricklaying.
How To: Remove Damaged Stripped Rusty Bolt with Vise Grip Pliers
This video will show you how to remove a stubborn,stripped,damaged or rusty bolt using a set of alligator Vise Grip pliers. Usually this will do the trick and get a bolt with a stripped head out for you.
How to Build a Shed, Part 15: Installing Exterior Wood Trim
In this video Henry shows you how to finish all the exterior trim on the shed. This video includes lot of tips to make the finish carpentry in this video easy and accurate.
How to Build a Shed, Part 12: Finishing the LP Smart Side Panels
Now that the Fascia Board and Soffit Materials have been installed, Henry shows you how to finish installing the LP Smart Side Panels.
How to Build a Shed, Part 10: Applying Roof Sheathing
Henry shows you the right way to install roof sheathing (1/2" Plywood) including the proper spacing and importance of using H-Clips to extend the life of your roof.
How To: Add a door In an exterior brick wall
If you've got a brick house and are looking to install a door in the brick, this how to will get you there. Be prepared, it's a big job and you'll need to be comfortable wielding several power tools. Are you ready to take the challenge?
How To: Sand cut and polish Perspex for a high-gloss finish
Need a smooth, polished, and glossy surfaced piece of acrylic for your next project? Then check out this video for a handy guide on how to sand, cut, and polish Perspex, a type of acrylic, for a high-gloss finish. Perspex is thick and difficult to work with, but this video will give you tips for a professional look.
How To: Fit a sleeved letter plate onto a letter box hole that's too big
While most of us have mailboxes from which we receive our deliveries, some of us still have small slits in our front doors known as letter box holes. This allows for the mailman to deliver mail straight into our homes, which is convenient for all intensive purposes.